Regency Fireplace Products B36XTCE Installation Manual download pdf (Page 63)

Regency B36XTCE Gas Fireplace

6363

INSTALLATION

OPERATING INSTRUCTIONS

OPERATING

INSTRUCTIONS

1) Read and understand these instructions

before operating this appliance.

2) Check to see that all wiring is correct and

enclosed to prevent possible shock.

3) Check to ensure there are no gas leaks.

4) Make sure the glass in the glass door frame

is properly positioned. Never operate the

appliance with the glass removed.

5) Verify that the venting and cap are

unobstructed.

6) The unit should never be turned off, and on

again without a minimum of a 60 second

wait.

LIGHTING

PROCEDURE

1) Press and release on ON/OFF button once

on the remote control or ON/OFF switch.

2) After approximately 4 seconds the spark

ignition system will spark for 60 seconds to

light the main burner.

3) The unit will turn on.

Note: The ﬁ rst try for ignition will last approxi-

mately 60 seconds. If there is no ﬂ ame ignition

(rectiﬁ cation) the board will stop sparking for

approximately 35 seconds. After wait time

, the board will start second try for ignition

by sparking for approximately 60 seconds .

If there is still no positive ignition the board

will go into lock out.

The system will need to be reset as follows:

a) Turn the system off using ON/OFF switch

or press ON/OFF button - if using optional

remote.

b) After approximately 2 seconds turn on ON/

OFF switch or press ON/OFF button if using

optional remote.

c) Repeat step 2.

SHUTDOWN

PROCEDURE

1) Turn the wall mounted switch or remote to

the "OFF" position.

2) Press "OFF" on the remote control.

IMPORTANT

To ignite or reignite the pilot, you

must ﬁ rst remove the glass door.

During the ﬁ rst few ﬁ res, a white ﬁ lm

may develop on the glass front as part of

the curing process. The glass should be

cleaned after the unit has cooled down

or the ﬁ lm will bake on and become very

difﬁ cult to remove. Use a non-abrasive

cleaner and DO NOT ATTEMPT TO CLEAN

THE GLASS WHILE IT IS HOT.

The FIRST FIRE in your heater is part of the paint

curing process. To ensure the paint is properly

cured, it is recommended you burn your ﬁ replace

for at least four (4) hours the ﬁ rst time.

When ﬁ rst operated, the unit will release an

odour caused by the curing of the paint and the

burning off of any oils remaining from manufac-

turing. Smoke detectors in the house may go off

at this time. Open a few windows to ventilate

the room for a couple of hours. The glass may

require cleaning.

NOTE: When the glass is cold and the appliance

is lit, it may cause condensation and fog

the glass. This condensation is normal

and will disappear in a few minutes as

the glass heats up.

DO NOT ATTEMPT TO CLEAN THE

GLASS WHILE IT IS STILL HOT!

DO NOT BURN THE UNIT WITHOUT THE

GLASS DOOR IN PLACE.

FIRST FIRE

NORMAL OPERATING

SOUNDS OF

GAS APPLIANCES

It is possible that you will hear some sounds from

your gas appliance. This is perfectly normal due to

the fact that there are various gauges and types

of steel used within your appliance. Listed below

are some examples. All are normal operating

sounds and should not be considered as defects

in your appliance.

Burner Tray:

The burner tray is positioned directly under the

burner and is made of a different gauge material

from the rest of the ﬁ rebox and body. Therefore,

the varying thicknesses of steel will expand and

contract at slightly different rates which can cause

"ticking" and "cracking" sounds. You should also

be aware that as there are temperature changes

within the unit these sounds will likely re-occur.

Again, this is normal for steel ﬁ reboxes.

Pilot Flame:

While the pilot ﬂ ame is on it can make a very

slight "whisper" sound.

Gas Control Valve:

As the gas control valve turns ON and OFF, a

dull clicking sound may be audible, this is normal

operation of a gas regulator or valve.

Unit Body/Firebox:

Different types and thicknesses of steel will

expand and contract at different rates resulting

in some "cracking" and "ticking" sounds will be

heard throughout the cycling process.

Blower Thermodisc:

When this thermally activated switch turns ON

it will create a small "clicking" sound. This is the

switch contacts closing and is normal.

1 2 ... 58 59 60 61 62 63 64 65 66 67 68 ... 71 72

Comments to this Manuals

No comments

Regency Fireplace Products B36XTCE Installation Manual Page 63

Comments to this Manuals

Related products and manuals for Fireplaces Regency Fireplace Products B36XTCE