Regency Fireplace Products B36XTCE Installation Manual download pdf (Page 65)

Regency B36XTCE Gas Fireplace

MAINTENANCE

liner, and subsequently dripping out the joints,

Continuous condensation can cause corrosion

of caps, pipe, and ﬁ ttings. It may be caused

by having excessive lateral runs, too many

elbows, and exterior portions of the system

being exposed to cold weather.

4) Inspect joints, to verify that no pipe sections or

ﬁ ttings have been disturbed, and consequently

loosened. Also check mechanical supports

such as Wall Straps, or plumbers' tape for

rigidity.

LOG REPLACEMENT

The unit should never be used with broken logs.

Turn off the gas valve and allow the unit to cool

before opening door and carefully remove the logs.

(The pilot light generates enough heat to burn

someone.) If for any reason a log should need

replacement, you must use the proper replacement

log. The position of these logs must be as shown

in the Diagrams under Log Installation.

Note: Improper positioning of logs may create

carbon build-up and will severely alter

the unit's performance which is not

covered under warranty.

GLASS GASKET

If the glass gasket requires replacement use a

tadpole glass gasket (Part # 936-155).

DOOR GLASS

Your Regency

ﬁ replace is supplied with high

temperature 5mm-Ceramic glass. If your glass

requires cleaning, we recommend using an

approved glass cleaner available at all authorized

dealers. Do not use abrasive materials.

CAUTION & WARNINGS:

* Do not clean when the glass is hot.

* The use of substitute glass will void all

product warranties.

* Care must be taken to avoid breakage of

the glass.

* Do not strike or abuse the glass.

* Do not operate this ﬁ replace without the

glass front or with a cracked or broken

glass front.

* Wear gloves when removing damaged or

broken glass.

* Replacement of the glass panels should be

done by a licensed or qualiﬁ ed service per

son.

GLASS REPLACEMENT

In the event that you break your glass by impact,

purchase your replacement from an authorized

Regency dealer only. Replacement glass (Part

#940-357/P) is shipped already installed into

the door frame. Reinstall as per Glass Door

Installation in the "Glass Door Removal" section.

MAINTENANCE

INSTRUCTIONS

1) Always turn off the gas valve before cleaning.

For relighting, refer to lighting instructions. Keep

the burner and control compartment clean by

brushing and vacuuming at least once a year.

When cleaning the logs, use a soft clean

paint brush as the logs are fragile and easily

damaged.

2) Clean appliance and door with a damp cloth

(never when unit is hot). Never use an abrasive

cleaner. The glass should be cleaned with a

gas ﬁ replace glass cleaner. The glass should

be cleaned when it starts looking cloudy.

3) The heater is ﬁ nished in a heat resistant

paint and should only be reﬁ nished with heat

resistant paint. Regency

uses StoveBright

Paint - Metallic Black #6309.

4) Make a periodic check of burner for proper

position and condition. Visually check the

ﬂ ame of the burner periodically, making sure

the ﬂ ames are steady; not lifting or ﬂ oating.

If there is a problem, call a qualiﬁ ed service

person.

5) The appliance and venting system must be

inspected before use, and at least annually,

by a qualiﬁ ed ﬁ eld service person, to ensure

that the ﬂ ow of combustion and ventilation air

is not obstructed.

Note: Never operate the appliance without the

glass properly secured in place.

6) Do not use this appliance if any part has been

under water. Immediately call a qualiﬁ ed service

technician to inspect the appliance and to

replace any part of the control system and any

gas control which has been under water.

7) In the event this appliance has been serviced

check that the vent-air system has been

properly resealed & reinstalled in accordance

with the manufacturer's instructions.

8) Verify operation after servicing.

General Vent Maintenance

Conduct an inspection of the venting system

semi-annually. Recommended areas to inspect

as follows:

1) Check the Venting System for corrosion in areas

that are exposed to the elements. These will

appear as rust spots or streaks, and in extreme

cases, holes. These components should be

replaced immediately.

2) Remove the Cap, and shine a ﬂ ashlight down

the Vent. Remove any bird nests, or other

foreign material.

3) Check for evidences of excessive condensation,

such as water droplets forming in the inner

1) Follow steps 1- 4 on page 53.

2) Remove 2 screws to remove light diffuser

plus gasket.

3) Replace the bulb - do not touch bulb with

bare hands, use gloves or bulb packaging

to protect bulb.

4) Reverse steps.

BULB REPLACEMENT

1 2 ... 60 61 62 63 64 65 66 67 68 69 70 71 72

Comments to this Manuals

No comments

Regency Fireplace Products B36XTCE Installation Manual Page 65

Comments to this Manuals

Related products and manuals for Fireplaces Regency Fireplace Products B36XTCE